







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Fence Installation: The Hialeah Owner’s Guide
CGI is a fence and outdoor-structure brand, and replacing a failed fence component with a CGI-compatible part in Hialeah typically runs $3,500 – $9,000 installed for a standard residential run. Scheduling usually starts with a free written estimate rather than a same-day swap, because the fence line, gate, and post footings need to be measured and matched before the quote is real. We are an independent service provider and are not affiliated with CGI.
The failure usually announces itself slowly. A gate that used to latch with one push starts catching on the strike. A post that was plumb last summer leans a quarter inch after the rainy season. Then the wind comes off the open ground west of the Palmetto and a panel sags. By the time an owner searches for a CGI replacement, the part is often less the problem than the whole assembly it belongs to – a fact worth knowing before you budget.
Which CGI Models This Applies To

CGI fence systems come in several product lines, and the parts are sized to the series. A panel or post from a six-foot privacy line will not mate cleanly with hardware from a four-foot picket line, and a gate leaf sized for one post spacing often will not hang straight on another. Before anything is ordered, confirm three things: the model or series number stamped on the post cap or gate hinge plate, a physical measurement of post spacing center-to-center, and the panel height. Those three data points tell us what replacement is compatible and what is a mismatched part waiting to fail.
The OEM-versus-aftermarket call matters here. CGI’s own parts carry the exact spec and the matching finish, which is the safest route when the fence is under a warranty. Quality aftermarket equivalents – same gauge, same powder-coat finish, correct post spacing – can deliver the same life at a lower number. The aftermarket part that fails is almost always a gauge or coating mismatch, not the brand. Bring the model number and a photo of the hinge or post base to the estimate. We also work across other brands, including KraftMaid, Cambria, and Silestone in the kitchen and countertop trades, but this page is CGI.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Fence Installation Is Failing
- Gate sag and strike misalignment. The hinge plates are pulling or the post has settled, usually because the footing was poured short in loose Hialeah soil. A gate that drags is a footing problem wearing a hinge costume.
- Post lean after the rainy season. South Florida’s water table and heavy summer rain soften footings that were set too shallow, and the post tilts a fraction that compounds each season.
- Powder coat chalking or rust bloom at the welds. Salt air and afternoon sun degrade a thin coating fast; rust at the weld line means the coat was sprayed thin at the joint, not that the metal was bad.
- Panel sag between posts. Fasteners backing out or rails bent from wind load leave the panels wandering below the top rail. Check the screws first – they’re the cheap fix.
- Loose or wobbling panels at the top rail. When a rail is no longer cinched, the panel moves with every gust and the vibration loosens the next fastener down the line.
Replacement Cost & What’s Included

A full CGI-compatible fence installation in Hialeah lands in the $3,500 – $9,000 range for a standard residential run. The number moves with fence length, material and finish, gate count and style, and footing depth – Hialeah’s ground and water table often require deeper post settings, which is labor and concrete, not guesswork. The quote you receive is a flat written price with a written scope before any work starts; under Clause 1 of the Haven Standard, that price is written before anyone picks up a tool.
| Line item | Typical range |
|---|---|
| CGI-compatible panel and post replacement (standard run) | $3,500 – $9,000 |
| Gate hardware and hinge re-set | Included in scope |
| Post footing correction (deeper set, concrete) | Bundled, quoted in writing |
| Finish match and coating touch-up | Included in scope |
No work proceeds on a change until the change order is signed, so the number you agreed to is the number you pay, within a few percent. Every visit includes a documented photo record of what we found and what we did, and the work carries our 365-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some checks are safe and worth doing yourself. Walk the line and push each post – if one moves, the footing is the problem. Tighten exposed fasteners with the right driver bit, and photograph any rust bloom so you can see whether it’s spreading. Those are observation tasks, not repair.
Where DIY goes wrong: resetting a post footing in Hialeah’s soil without proper depth and concrete, re-hanging a gate leaf without checking plumb and strike alignment, and re-coating a powder finish without the correct product. A gate that sags onto a child’s fingers or a fence run that fails in the first storm is the cost of a home fix that looked close enough. If the post moves or the gate drags, that’s a structural call. Call (888) 836-5914 for a free written estimate.
FAQs

A correctly installed, well-coated CGI fence typically lasts 15 to 20 years in South Florida, with salt air and summer sun shortening the upper end of that range. Coatings wear faster on fence facing the afternoon sun, so a finish touch-up every few years buys years of life. Call (888) 836-5914 for an exact quote on a replacement – estimates are free.
Often yes. A single panel, a hinge set, or one footing can usually be repaired without touching the rest of the run, which keeps the cost well below a full install. The written estimate tells you honestly which route your fence needs – repair or replace – before you commit. Call (888) 836-5914 for a free second opinion on any written estimate.
A standard residential run in Hialeah usually takes one to two days once the part is confirmed and on site, longer if multiple footings need correcting. We schedule to a confirmed date rather than a promise of “today.” Call (888) 836-5914 to get your written price and a scheduled date.
We match the model or series number and the measured post spacing against OEM and quality aftermarket equivalents, then tell you which is compatible and why. We don’t carry parts on a truck – the part is ordered to your fence spec, not pulled from stock. Call (888) 836-5914 to start with a free estimate.
Get Your Written Price
If your CGI fence has a sagging gate, a leaning post, or a panel that won’t stay put, the fastest way to a real number is a call. Rowan Construction Group Hialeah delivers a flat written price with a written scope before any work starts, a documented photo record on every visit, and the 365-Day Done Right Promise backing the result. Our technicians have up to 19 years of experience, and a live person answers calls 24/7. Bring a competitor’s quote and we’ll review it line by line at no charge. Call (888) 836-5914 to schedule your free estimate.
Written by the team at Rowan Construction Group Hialeah, serving Hialeah and nearby areas.












