







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CertainTeed Bathroom Remodeling: The Hialeah Owner’s Guide
A CertainTeed bathroom remodel in Hialeah typically costs $9,000 – $28,000 installed, depending on what’s failing and how much of the assembly gets replaced. Smaller scopes, such as a moisture-damaged board swap or a shower surround replacement, come in at $5,000 – $12,000. We work with CertainTeed-compatible products and systems across Hialeah, and we tell you the price in writing before any work starts.
Most owners don’t find a CertainTeed bathroom failure by reading a label. They find it with their hand. A soft spot at the base of the shower wall. A grout line that keeps coming back after every re-caulk. A little gray bloom behind the toilet that wasn’t there last spring. That’s how failing backer board and moisture barriers announce themselves in South Florida: not with a crash, but with a stain that grows.
Key Takeaways
- CertainTeed backer board and moisture-barrier systems fail most often at seams and penetrations, not in the field of the panel.
- Installed Hialeah bathroom remodels run $9,000 – $28,000; small bathrooms $5,000 – $12,000; walk-in showers $4,500 – $12,000.
- Florida’s humidity means barrier failures show up as mold and soft substrate within 2 – 4 years, faster than most national guidance assumes.
- We’re an independent contractor and not affiliated with CertainTeed. We work with their products and compatible alternatives.
Which CertainTeed Models This Applies To

CertainTeed’s bathroom-side products aren’t a single model line, and that’s the first thing to understand before you start matching parts. The family breaks into three buckets you’ll actually encounter in a Hialeah bathroom:
- Backer board and tile substrate. CertainTeed’s cement and fiber-cement board lines come in thicknesses of 1/4 inch, 1/2 inch, and 5/8 inch. The thickness is stamped on the face of the panel. Match what’s there, because swapping 1/2 inch for 1/4 inch changes your finished wall depth and throws off tile transitions at the shower curb and door casing.
- Moisture and waterproofing membranes. Sheet and liquid-applied barrier systems that sit between the substrate and the tile. These carry their own brand-specific accessories: seam tape, corner pieces, and drain collars. A generic membrane patch on a branded sheet membrane is a compatibility failure waiting to happen.
- Gypsum and mold-resistant wallboard. Standard, moisture-resistant, and enhanced moisture-resistant board, marked on the paper face and the edge tape. The board at the back of a Hialeah shower isn’t the same board on the ceiling over your vanity, and it shouldn’t be.
How to identify what you have. Pull the manufacturer stamp off the exposed edge of any panel at a cut, or look for the printed face marking. Measure the panel thickness with a tape, measure the seam width, and photograph the drain collar and the waterproofing seams at the corners before anything gets covered. If you can’t find a label, the measurements and photos are enough for us to tell you what family it belongs to.
OEM versus quality equivalent. For backer board and membrane systems, we’ll install the CertainTeed-compatible product if that’s what’s spec’d, and we’ll tell you honestly when a quality equivalent from another manufacturer meets the same spec at a lower material cost. The membrane under your tile doesn’t care about the name on the box; it cares whether the seams are taped and the corners are reinforced. What matters is a matched system: brand-specific tape, brand-specific corners, brand-specific drain collars. Mixing brands at the seams is where we see the most avoidable failures. We also work with KraftMaid, Cambria, and Silestone when a Hialeah bathroom remodel moves into cabinetry and countertops.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CertainTeed Bathroom Remodeling Is Failing
These five symptoms show up again and again in Hialeah bathrooms, and each one points to a specific failure underneath the finish.
- Grout that cracks along a straight line, repeatedly. A crack that reappears along the same grout joint after re-caulking usually means movement in the substrate, not a grout problem. In Hialeah’s older homes, that’s often a backer board panel that was never properly fastened or never had a seam taped.
- Soft or spongy wall at the shower base or behind the toilet. Water has gotten past the moisture barrier and into the board. By the time you can feel it with your thumb, the panel has been wet through a full rainy season.
- Dark staining or a musty smell behind the vanity or toilet. CertainTeed mold-resistant board is resistant, not immune. A barrier breach at a plumbing penetration lets moisture wick in, and South Florida’s ambient humidity keeps it wet. This shows up in Hialeah bathrooms in two to four years, not the ten most general guidance implies.
- Loose tiles that sound hollow when tapped. Hollow sound means the bond failed, and lost bond almost always traces to a moisture barrier that trapped water against the back of the assembly rather than shedding it.
- Efflorescence, that white chalky bloom, at the tile base or grout lines. Mineral salts pushed to the surface by water migrating through the assembly. It’s a moisture map, and it tells you where the barrier is compromised.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what a Hialeah bathroom remodel runs when the failure is a substrate or barrier problem, priced as an installed number, not a parts number:
| Scope | Installed Price Range |
|---|---|
| Bathroom remodel, full | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
What drives the range: how much of the assembly is wet and has to come out, whether the failure reached framing, whether the plumbing rough-in is being moved, and whether tile is being matched or fully replaced. A localized backer board and membrane replacement at one shower wall sits at the low end. A gut remodel that pulls the tub and reworks the drain is at the high end.
What’s included: removal and disposal of the failed substrate, new certainteed-compatible backer board and waterproofing with matched seam tape and corners, tile or surround, and a written scope before anyone picks up a tool. The price is a flat number. If a change comes up once walls are open, we don’t proceed until you’ve signed the change order. The work carries our 365-Day Done Right Promise. Call (888) 836-5914 for a free estimate.
DIY or Call Us?
Some of this an owner can check safely, and some of it will cost you far more than it saves.
Safe to check yourself: tap tile for hollow sound, look for efflorescence and dark staining, press the wall at the shower base and behind the toilet, and photograph the exposed panel edges and any labels you can see. That’s diagnosis, and it’s useful.
Where it goes wrong: the waterproofing itself. A barrier system is only as good as its seams, and seam taping plus corner reinforcement is where nearly every failure we open up in Hialeah started. Cutting out a section of board, patching a membrane, and re-tiling over it looks fine and fails within a couple of seasons. The membrane is buried under tile, so you won’t get a second look at it without tearing everything out again. Water that reaches framing and stays there is a genuinely expensive problem.
If you’re weighing a patch against a proper repair, call us at (888) 836-5914. Estimates are free, and we’ll give you the honest read on whether you’re looking at a $400 caulk-and-grout issue or a $9,000 assembly replacement.
FAQs

Properly installed, a backer board and membrane system should last 20 years or more. In Hialeah’s humidity, though, an installation with an untaped seam or a breached penetration tends to show visible failure in two to four years, because the moisture never gets a dry-out window between rainy seasons. Lifespan here depends more on installation detail than on the product. Call (888) 836-5914 for an exact quote, and estimates are free.
Sometimes yes. A single failing seam or a localized moisture breach at one shower wall can be repaired by removing the affected panels, replacing them, and re-waterproofing with matched tape and corners. Once the failure has spread along a whole wall or reached the framing, replacement is the cheaper path. We’ll tell you which you’re looking at before we quote. Call (888) 836-5914 to schedule your free estimate.
A localized substrate and membrane repair runs a few days. A full Hialeah bathroom remodel with tile, a new shower pan, and a vanity runs two to four weeks depending on scope and tile lead times. You get a written schedule with the written price, so the timeline isn’t a moving target. Call (888) 836-5914 for a flat written quote.
We match the existing specification first, the thickness and membrane family, then quote the certainteed-compatible product against a spec-equivalent alternative and show you both numbers in the written estimate. You choose. We’re an independent contractor, not affiliated with CertainTeed. Call (888) 836-5914 for the free estimate, and if you already have a competitor’s written quote, we’ll review it line by line at no charge as a free second opinion.
One more thing before you call: we’re Rowan Construction Group Hialeah, and we put the price in writing before any work starts. That’s the whole idea behind the Haven Standard. Our technicians have up to 19 years of experience, crews are background-checked and uniformed, every visit includes a documented photo record, and a live person answers the phone. Call (888) 836-5914 for a free estimate on your Hialeah bathroom.
Written by the team at Rowan Construction Group Hialeah, serving Hialeah and nearby areas.












