







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Windows & Doors: The Hialeah Owner’s Guide
We install and service Mr-Glass windows and doors for homeowners across Hialeah, and the installed price typically lands between $4,500 and $15,000 for a whole-house window replacement, or $8,000 to $25,000 when you step up to impact-rated units. Parts-level repairs, like a failed balance, sash lock, or weatherstripping run, are quoted individually after we see the unit. Most window and door work is scheduled rather than same-day; we’ll give you a written date when you book.
Owners in Hialeah usually find us one of two ways. Either a window that used to open with one finger now needs a shoulder, or a door that sealed tight during the last dry season now whistles and lets water past the threshold after an afternoon storm. Both are symptoms, not the problem itself. We’re an independent service provider and not affiliated with Mr-Glass, so our job is to match the right part to your exact unit and put the number in writing before we touch anything.
Which Mr-Glass Models This Applies To

Mr-Glass has sold a range of residential window and door lines over the years, and the parts are not interchangeable across them. The single most common mistake we see in Hialeah is a homeowner ordering a replacement balance or sash operator based on a photo, then discovering the mounting hole spacing is off by a quarter inch. The fix starts with identification, not with a purchase.
Here’s how to confirm what you have before anyone quotes a part:
- Check the glass etch. Every tempered or impact-rated unit carries a small permanent stamp in one corner, usually a manufacturer code and a safety standard number. Photograph it with the light at an angle.
- Read the label inside the frame. Most Mr-Glass units have a sticker or etched model line along the top or side jamb, visible with the sash open. That code tells us the series and the hardware family.
- Measure the sash, not the opening. Width and height of the moving panel, plus the visible glass area, separate one hardware family from another.
On the OEM-versus-aftermarket question: for structural and impact components we lean OEM or a documented equivalent, because Florida product approval is tied to the tested assembly and a mismatched part can void that approval. For wear items like weatherstripping, sash locks, and rollers, a quality aftermarket part is often the same durometer and profile at a lower price, and we’ll tell you which is which in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Mr-Glass Windows & Doors Is Failing
South Florida weather is hard on window and door hardware in a specific way. The heat and humidity cycle the frame and sash dozens of times a day, which works fasteners loose and dries out seals that were fine two summers ago. Here’s what that looks like in practice.
- The sash won’t stay up. A double-hung that slides down on its own means the balance spring or block-and-tackle has lost tension. It’s a wear item with a finite cycle count, not a sign the whole window is finished.
- Water pooling on the interior sill after rain. Usually the weep system or the sill seal, not the glass. Impact-rated units shed a lot of water in a Hialeah downpour, and a clogged or degraded weep path sends it inside.
- A whistle or draft around the frame. Weatherstripping and corner seals compress and crack with UV exposure. This is one of the few failures you can hear before you see.
- Fogging between the panes. That’s a failed seal in the insulated glass unit, and it’s a glass replacement rather than a hardware fix. Once moisture is inside, the low-E coating is compromised.
- The lock won’t fully engage, or the door drags. On hinged doors this is usually hinge sag or a shifted strike plate; on sliders it’s worn rollers. Left alone, a door that doesn’t latch is a security gap and a water intrusion point.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Prices for Hialeah depend on the unit count, the frame material, and whether you’re replacing glass only, hardware only, or the whole assembly. Here’s what we quote:
| Scope | Typical installed range |
|---|---|
| Window replacement (whole-house, standard) | $4,500 – $15,000 |
| Impact window installation | $8,000 – $25,000 |
| Individual part or hardware repair | Quoted after inspection |
What drives the range: number of openings, impact versus non-impact rating, frame material, and whether the existing opening needs reframing. Every quote is a flat written price with a written scope, and no change proceeds without a signed change order. Labor, disposal, and sealing are included in the number. The 365-Day Done Right Promise covers the workmanship, and every visit comes with a documented photo record of what we found and what we did.
DIY or Call Us?
Some checks are genuinely safe and worth doing yourself. Cleaning a weep hole, wiping down and inspecting weatherstripping for cracks, and photographing your glass etch and frame label cost nothing and help us quote accurately.
Where DIY goes wrong: replacing a balance on a double-hung, re-hanging a sagging door, or resetting an insulated glass unit. The balance is a spring under load, and releasing it incorrectly can snap the hardware back hard enough to break glass or injure a hand. On impact-rated units, an improperly seated part can compromise the rated assembly, which matters both for water intrusion and for insurance. Our technicians have up to 19 years of experience, are background-checked and uniformed, and we’re happy to tell you honestly whether a part swap is worth it or whether the unit is at the end of its life. Call (888) 836-5914 for a free written estimate.
FAQs

Hardware like balances, locks, and rollers typically lasts 10 to 15 years in South Florida’s heat-and-humidity cycle, while the insulated glass unit often lasts longer before a seal fails. Impact-rated assemblies tend to hold their rating well past that, but seals and weatherstripping wear faster here than in drier climates. We’ll assess the actual condition of your unit and give you a written recommendation. Call (888) 836-5914 for an exact quote on your Hialeah home.
Often yes, and we’ll say so when it’s true. A failed balance, sash lock, roller, or weather seal is usually a discrete part swap rather than a whole-unit replacement. The exception is a fogged insulated glass unit or a cracked frame, which is a replacement job. Call (888) 836-5914 and we’ll tell you which one you’re looking at before you spend.
Most single-part hardware repairs are done in a couple of hours once the correct part is matched to your model. Whole-window or door replacement is scheduled across a day or more depending on unit count, and we give you the written timeline when you book. Call (888) 836-5914 to schedule your free estimate.
We identify your series from the glass etch and frame label, then source OEM or a documented equivalent through our network of vetted material brands. Because we’re independent and not affiliated with Mr-Glass, we can offer both the factory part and a quality aftermarket match, and we put the difference in writing so you can decide. We also service KraftMaid, Cambria, and Silestone products across other trades. Call (888) 836-5914 for a free estimate.
Written by the team at Rowan Construction Group Hialeah, serving Hialeah and nearby areas.












