







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
James Hardie Home Additions & ADU: The Hialeah Owner’s Guide
We build and finish home additions and ADUs clad in James Hardie fiber cement in Hialeah, and installed projects here run $45,000 – $130,000 for an addition and $90,000 – $220,000 for a detached ADU. James Hardie isn’t a machine with a serial number, so there’s no “failed part” to swap: the failures owners call us about are siding and trim problems on an existing addition, a converted garage, or a rear extension. Most people spot it after a rainy week, when paint bubbles along the bottom course or a corner starts to look soft to the touch. That’s where this page starts.
A quick note on who we are: Rowan Construction Group Hialeah is an independent contractor and is not affiliated with James Hardie. We install, repair, and re-clad with James Hardie products because they hold up in South Florida heat and humidity better than the alternatives we’ve worked with, not because we speak for the manufacturer.
Which James Hardie Models This Applies To

James Hardie siding and trim are sold as product lines, not model numbers, so matching the right replacement starts with identifying the line and thickness on your wall. The three you’ll see on Hialeah additions are HardiePlank lap siding, HardiePanel vertical siding, and HardieTrim boards at the corners, windows, and fascia. Lap siding comes in a few exposure widths, with 6-1/4 and 8-1/4 inch face exposures being the most common, and thickness varies by product. That matters: if you replace one course with the wrong thickness, the shadow lines won’t line up and you’ll see it from the street.
How to identify what you have: look at the back of a loose piece or a piece in the scrap pile for the printed stamp, which carries the product name and thickness. No stamp visible? Measure the exposed face width of a course and the overall thickness at an edge. For trim, HardieTrim comes in different thicknesses (5/4 and 4/4 are the usual residential sizes), and mixing them shows up as a step at the corner board.
OEM versus aftermarket for James Hardie is a real decision. The genuine article is a fiber cement product with a known formulation and a manufacturer finish warranty on pre-finished boards. Quality fiber cement equivalents exist at lower cost, but they’re not identical in density or finish, and we tell homeowners which is which before quoting. What we don’t do is claim we stock James Hardie parts or carry them on a truck. Material is sourced per project against the written scope, and we say so on the quote.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your James Hardie Home Additions & ADU Is Failing
Fiber cement is durable, but it fails in predictable ways in Hialeah’s climate, and the cause matters more than the symptom. Here’s what we find most often:
- Paint bubbling or peeling along the bottom course. This usually points to water wicking up from the ground or a missing weep screed at the base of the wall, so moisture has nowhere to drain. It’s a drainage detail problem more than a siding problem.
- Soft or crumbly spots near corners and window trim. Caulk joints that have aged out let water sit against the board edge. Fiber cement doesn’t rot the way wood does, but repeated wetting breaks down the edge and paint won’t hold there.
- Visible gaps or movement at butt joints. Boards expand and contract with heat, and if the installer butted them tight with no gap, the joints crack and open. Hialeah’s summer temperature swings make this worse on south- and west-facing walls.
- Mildew that keeps coming back after cleaning. On a shaded north wall or under a deep soffit, mildew that returns within weeks usually means the finish coat is thin or the wall stays damp. It’s a coating and ventilation issue, not a reason to replace the siding.
- Chalking or a white powder you can wipe off. That’s the factory finish breaking down under UV. It’s cosmetic at first, but once the surface chalks, new paint won’t adhere without proper prep.
One lifespan reality worth knowing: in South Florida sun and rain, a factory finish on fiber cement typically needs repainting in the 8-to-12 year range, faster on full-sun walls. A board that’s failing at year four usually has an installation or drainage problem behind it, and re-cladding without fixing the cause just resets the clock.
Replacement Cost & What’s Included

Pricing for James Hardie work on a Hialeah addition depends on square footage, how much trim needs replacing, and whether we’re fixing the drainage detail underneath. Here’s the honest range for the projects we quote:
| Scope | Typical installed range in Hialeah |
|---|---|
| Home addition, full build with James Hardie cladding | $45,000 – $130,000 |
| ADU construction, detached | $90,000 – $220,000 |
| Garage conversion to living space | $30,000 – $80,000 |
For a repair rather than a full build, the number tracks the square footage of siding and trim plus what’s behind it. What drives the range: wall area, trim linear footage, whether the weep screed or flashing is missing, and whether we’re matching a discontinued line. Under Clause 1 of the Haven Standard, the price is written before anyone starts, itemized by material and labor so you can see both. No work proceeds on a change until the change order is signed, and the work carries our 365-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
There’s a safe half of this and a half that isn’t. You can walk the perimeter after a hard rain and note where water pools against the wall, check caulk joints at windows and corners for cracks, and wipe a board to see if white chalk comes off on your finger. Those checks cost nothing and tell you whether the problem is surface or structural.
Where DIY goes wrong: cutting and fitting fiber cement safely means handling a heavy, silica-containing board, and the respiratory protection and cutting method matter. More importantly, if the real problem is missing flashing or a bad weep screed, replacing the visible board hides the water path and it comes back within a season. We’ve seen that repair done twice on the same Hialeah wall. The fix is in the assembly, not the board. If you’re unsure which you’re looking at, call (888) 836-5914 and we’ll look at it with you at no charge.
FAQs

The board itself can last decades, but the finish is the part that ages. In Hialeah’s sun and humidity, plan on repainting the factory finish every 8 to 12 years, sooner on unshaded south and west walls. Lifespan is really about the drainage detail behind the board, so a wall installed with proper flashing and a weep screed outlasts one that wasn’t.
Often yes. Localized damage at corners or under windows can be cut out and patched with matching material, and mildew or chalking is a cleaning-and-recoat job, not a replacement. Full replacement is only necessary when the damage is widespread or the underlying water problem can’t be corrected board by board. We’ll tell you which one you’re facing in writing.
A localized repair is usually a day or two. Re-cladding a full wall or an addition runs longer depending on square footage and whether we’re correcting flashing and drainage. We put the timeline in the written scope so you know what to expect before the crew arrives. Call (888) 836-5914 for a free estimate on your specific project.
We source per project against the written scope, matching the product line and thickness to what’s already on your wall, so the new courses line up with the old. We don’t keep James Hardie parts in stock or carry them on a truck, and we say that upfront rather than implying otherwise. That also means we can quote a genuine James Hardie product or a quality equivalent side by side so you can decide.
We also work with KraftMaid, Cambria, and Silestone on the interior side of additions and ADU build-outs, so a project that touches both the shell and the kitchen gets one written scope instead of two.
Get a Written Price on Your Hialeah Project
Whether you’re chasing a soft corner on an existing addition or starting a new ADU from the slab up, the next step is the same: a written price with a written scope before anyone picks up a tool. Our technicians have up to 19 years of experience, crews are background-checked and uniformed, and every visit includes a documented photo record as a standard deliverable. Bring a competitor’s estimate and we’ll review it line by line at no charge through our Free Second Opinion. Call (888) 836-5914 for a free estimate.
Written by the team at Rowan Construction Group Hialeah, serving Hialeah and nearby areas.












