







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mighty Buildings Home Additions & ADU: The Hialeah Owner’s Guide
We install and finish Mighty Buildings-compatible home additions and ADUs for Hialeah owners, and a typical project here runs $45,000 – $130,000 for an addition, $90,000 – $220,000 for a detached ADU, and $30,000 – $80,000 for a garage conversion. These are planned builds, not emergency calls, so we schedule them properly and put the price in writing before anyone touches the site.
Owners usually discover a problem slowly. A panel seam that was tight in year one starts showing a hairline gap after a wet season. The mini-split in a finished ADU struggles to hold temperature in August. A door sticks, then stops latching. Or the slab-to-wall junction in a Hialeah garage conversion shows a moisture stain that wasn’t there last summer. Mighty Buildings panels are factory-made and precision-cut, which is a real advantage – but precision panels still sit on a site-built foundation, and in South Florida that foundation and the connections to it are where most failures begin.
Key Takeaways
- Installed addition pricing in Hialeah: $45,000 – $130,000. ADU: $90,000 – $220,000. Garage conversion: $30,000 – $80,000.
- Most “part failures” on a Mighty Buildings unit trace to the foundation interface, the panel joints, or the mechanicals – not the panels themselves.
- Rowan Construction Group Hialeah is an independent contractor. We are not affiliated with Mighty Buildings.
- Every job gets a flat written price, a signed scope, and a documented photo record.
Which Mighty Buildings Models This Applies To

Mighty Buildings has produced a few distinct product lines, and the one on your property changes what we’re looking at. The company’s early work centered on its Mighty Mods accessory units and the larger Mighty House panels, with a 3D-printed exterior panel system in the mix. Older installs may use one generation of panel and connection detail; newer ones use another. The differences matter when you need a compatible panel, a matching trim piece, or a mechanical unit sized for the assembly.
How to identify what you have: look for a data plate or label inside the unit, usually near the electrical panel or on the interior face of an exterior panel. It will list the model line and a production or serial reference. If there’s no label, we measure. Panel module width, wall thickness, and the profile of the connection spline are the three measurements that tell us which generation you’re dealing with.
On OEM versus aftermarket: for structural panels and the proprietary connection hardware, OEM is the honest answer. A generic panel won’t match the spline profile, and forcing a fit is how you get the water intrusion that starts a bigger problem. For finishes, trim, doors, mechanicals, and fixtures, quality aftermarket equivalents are often the smarter buy, and we’ll say so. We don’t claim to stock Mighty Buildings parts and we don’t carry them on a truck – we source them per job and tell you the lead time up front.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Mighty Buildings Home Additions & ADU Is Failing
- Hairline cracks or gaps at panel seams. These usually trace to foundation settlement or thermal movement the connection detail wasn’t allowed for. In Hialeah’s afternoon storm cycles, water finds a 1/16-inch gap fast, and that gap widens each wet season if it isn’t addressed.
- Moisture staining or efflorescence at the slab-to-wall junction. Efflorescence is the white mineral bloom left when water moves through concrete. It means moisture is traveling where it shouldn’t, often through a compromised flashing or a slab edge that wasn’t detailed for our water table.
- Doors and windows that stick or stop latching. On a precision-built unit, this is rarely the door. It’s the frame moving, which points back to the foundation or the connection to it.
- The ADU’s mini-split can’t hold temperature in summer. A unit sized for a temperate climate won’t keep up with a Hialeah August. Undersized mechanicals and envelope air leakage are the usual cause, and both are fixable.
- Roof or parapet flashing that’s lifted or sealed with caulk instead of detailed properly. Caulk is a maintenance item, not a flashing. Once it fails, water tracks along the panel face and shows up as a ceiling stain well away from the actual leak.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what these projects run in Hialeah, installed, with the price written before work starts:
| Project | Installed Range (Hialeah) |
|---|---|
| Home addition (Mighty Buildings-compatible) | $45,000 – $130,000 |
| ADU construction | $90,000 – $220,000 |
| Garage conversion | $30,000 – $80,000 |
What drives the range: foundation type and soil conditions (Hialeah’s high water table and limestone mean a different foundation detail than a dry-climate install), the number of panel connections, whether the mechanicals need upsizing for our climate, and the finish level inside. A garage conversion sits at the low end because the shell and slab already exist; a detached ADU sits at the high end because everything is new, including the utility runs.
Our quotes are flat and line-itemed: the parts, the labor, the foundation work, the permits, and the finish are each a written line. No change proceeds without a signed change order. The work carries our 365-Day Done Right Promise – if it isn’t done right, we make it right – and you get a documented photo record of what we found and what we did, as a standard deliverable.
DIY or Call Us?
Some things you can safely check yourself. Walk the perimeter and look for gaps at panel seams. Photograph any staining at the slab line. Note which doors and windows stick and when. Check that your HVAC or mini-split filter is clean and confirm the unit’s rated capacity against the square footage. Those observations are useful and we’ll take them.
What you shouldn’t do yourself: re-sealing panel joints, adjusting or re-flashing a roof connection, or moving any structural or load-bearing component of a prefab assembly. These aren’t dangerous the way a spring or a live panel is, but a wrong fix here traps moisture inside a wall assembly, and by the time you see it, the repair is five figures instead of a service call. The connection details on a Mighty Buildings unit are specific, and getting them wrong is the most common way a small issue becomes a big one.
Call (888) 836-5914 and we’ll walk you through what to look at and what it likely means – free estimate, no pressure.
FAQs

The panel assembly itself is built to last decades, and factory precision is part of why. The real variables are the foundation, the flashing, and the mechanicals – those are what determine whether you get 30 years or 15 in South Florida’s heat and rain. Get the foundation and envelope detailing right and the panels will outlast the rest of the house. Call (888) 836-5914 for an exact assessment and quote.
Usually, yes. Most of what we’re called out for on a Mighty Buildings unit is foundation, flashing, joint, or mechanical work – not a full panel replacement. A lifted flashing, a failed sealant joint, a settling slab edge, or an undersized mini-split are all repairable at a fraction of replacement cost. We’ll tell you honestly when repair is the right call. Call (888) 836-5914 for a free second opinion.
Repairs and finish work typically run a few days to a couple of weeks depending on scope. A full addition or ADU is a multi-month build, and we give you a written schedule with the written price. Hialeah permitting and inspection timelines are part of that estimate, not an afterthought. Call (888) 836-5914 to get your project scoped.
We source per job against your model line and measurements, and we tell you the lead time before you commit. For proprietary structural panels and connection hardware we go OEM; for finishes and mechanicals we recommend quality aftermarket equivalents where they’re the better value. We don’t claim to stock Mighty Buildings parts. Call (888) 836-5914 and we’ll confirm what your unit needs.
We also work with KraftMaid, Cambria, and Silestone on the finish side of these projects when the addition includes a kitchen or bath.
If you have a Mighty Buildings unit in Hialeah that’s showing its age, the next step is a free estimate. We’ll look at the foundation, the envelope, and the mechanicals, put the findings in writing with a flat price and a written scope, and stand behind it with the 365-Day Done Right Promise. Call (888) 836-5914 to schedule your free estimate.
Written by the team at Rowan Construction Group Hialeah, serving Hialeah and nearby areas.












